Due to the constant increase of the electricity price, all types of customers must find new formulas to reduce their electricity bill. To succeed in this, we are presenting our new power management system to control the maximum demand: MDC series (MDC 4 and MDC 20).
It is necessary to understand the different terms which appear in an electricity bill to identify where we can act to reduce it. Of all the concepts, the most important ones are: Active energy term, reactive energy term and, in some countries, the maximum demand term, being this one last the subject of this article.
As described below, an optimal management of the contracted power allows us to:
Spanish bill simulation | Active energy term Maximum demand term or Maximum demand indicator (MDI) Reactive energy term |
The maximum demand value is the average from the instantaneous power (in kW or kVA) during a defined time interval, usually every 15 minutes (this time interval will depend on each country). There are different methods to calculate this parameter:
Fixed window (Block window)
This is the maximum demand calculation during a defined interval (usually every 15 minutes). Once the data is obtained, the value is stored and it makes a reset to start a new calculation for the next 15 minutes. This 4 registers will be measured every hour.
Sliding Window
This is the maximum demand calculation during a defined interval (usually every 15 minutes). Once the data is obtained, it will wait one minute to start a new 15 minutes calculation (this time may vary depending on the country). This means that every minute (this time can depends on the meter) it will record one maximum demand value from the last 15-minute period. This 60 registers will be measured every hour.
To avoid penalties for maximum demand we must ensure that this value will never exceed contracted power.
Usually in electricity bills, the highest maximum demand value recorded by the meter is compared to the contracted power. Whenever this value is higher than the contracted power, there will be an economic penalty. Therefore, if during the billing month the power exceeds the one contracted, during a period of 15 minutes, the customer will pay a penalty, even if it exceeds only once a month (one month has approximately 2880 fifteen-minute periods).
For the particular case of Spain, depending on the maximum demand value, the penalty can involve a very significant bill increase, as described in the following graph:
Maximum demand term increase depending on the Contracted power exceeds (Spain- for tariffs 3.0 and 3.1)
As shown in the graph, if the maximum demand value exceeds 10 % of the contracted power, the user will pay a 20% increase on the maximum demand term. However if the maximum demand value exceeds 20 % of the contracted power, the user will pay a 50% increase on the maximum demand term.
As we have been advancing, the goal to control the maximum demand is to not exceed the limit of the contracted power. To archive this goal, we advise to install a system able to disconnect non critical loads, on different time periods, and also avoid connecting loads simultaneously to reduce the instantaneous power.
Non-critical loads are those that do not affect the main production process or that are not essential, such as:
The main objective of the new CIRCUTOR MDC series is to manage and control the maximum demand of an installation. To achieve this objective, the device connects and disconnects some loads (non-critical ones) to ensure that the maximum demand will never be higher than the contracted power, avoiding electricity bill surprises. Moreover, the extended MDC 20 range, allows a tariff control to adjust the loads for being connected on periods with lower price, avoiding high consumptions due to loads simultaneity during high tariff price periods.
MDC 4 device | MDC 20 device |
MDC 4 is perfect for those installations which need a basic maximum demand control. Following some easy configuration steps the user will define up to 4 maximum power levels to start disconnecting non-critical loads.
Furthermore, MDC 4 incorporates an internal power analyzer for the maximum demand calculation (it also records electrical parameters such as voltage, current and power). Every time MDC 4 detects a power excess, this will disconnect several lines with non-critical loads, reducing automatically the instantaneous power. This will ensure that the installation will not exceed the maximum demand limit, hence avoiding penalties on the next electricity bill.
Operation method of MDC 4
MDC 4 |
|
MDC 20 is a data logger with an integrated web server meant to manage and control the maximum demand. Its versatility allows the user to do basic or advanced configurations. MDC 20 manages non-critical loads to ensure that the maximum demand value will never exceed the contracted power, avoiding penalties for power excess.
MDC 20 has an Ethernet port and a RS-485 communication channel (Modbus RTU), 6 relay outputs for load management and 8 digital inputs for collecting pulses (from other meters) or for logical states (opened-closed). It is expandable up to 48 relay outputs and 48 digital inputs by connecting 12 LM 4I/O devices via RS-485 communications (with 4 inputs/outputs each one).
The device has an internal data base (more than one year of data) with an integrated web server with PowerStudio software for programming, configuring and monitoring the device status and the associated peripheral devices connected by RS-485. Furthermore, it graphically shows the simulation of the system behavior according to the programmed settings.
MDC 20 infrastructure
MDC 20 |
|
Click here to obtain more information about MDC 4 and MDC 20
New MDC series to manage and control the maximum demand
You can also follow our publications on CIRCUTOR's Twitter account, and on LinkedIn.
WRITTEN BY CIRCUTOR